thanks dwayo. i tried making a mountain time trial and got a heap of errors about the slope. apart from moving the route and deleting some corners, how do you smooth out a hill to meet the slope requirement.

also i had a road error where the course went at right angles and it had like a small gap in the road???

I just have 1 question. What are the requirements to place ArriveTDF_Mont ? I made a Montaigne stage but i cant place ArriveTDF_Mont where i want (in the top of climbing) i can place it with 16 kms bellow so i lose a lot from my climbing finish,sry for my bad english.Thanks

are you sure there is 2 km rout after the place you put your finish line?

and i think it can't be more then a few % at the place of your finish - but this i'm not sure of

well i thing that is the problem because i have more than 14 kms but the last 14 kms average pente (slope) is 20 % and the pente where they let me to put the ArriveTdf is 12-16%

hey guys just wondering but i cant figure this stuff out:

1) Change color/texture of the road.
2) Create islands.

hey guys

how can i import stages into the game so i can play it?

I already answered you in your own thread: https://pcmdaily.com/forum/viewthread....d_id=13672

yes i know you did but it will be nice if i have somethin in english

It's because there are 2 seperate road segments, i.e. it's an intersection, the problem is the editor can't cope with a 2-way intersection, I think it gets confused!
To solve the problem, either add a third road that intersects at that point, or else delete one of the segments all the way back to the next intersection and continue the first all the way to that intersection... You see what I mean? Sorry if it's a bit confusing...

1) In the road options on the right (after clicking on a waypoint), it's one of the dropdown options, I can't remember what it's called but it's probably fairly obvious.

2) This is a little more tricky (to do and explain!), when using the water tool you need to loop back around on yourself. Basicly on one side of the line you create there will be water and on the other there will be land, so you need cut into the water and create a loop and then go back to where you were... Hmmm not very explicit, I'll add a picture of what you need to do tonight, i can't right now, I'm at work! Back to scorecards!


Edit: Ok I have some programs running so I can waste time here! The stunning artwork attached will hopefully help you understand
So the little green Cyprus shaped object in the middle is the island you want to create, the blue is the water and the green around is land, we'll get to the rest in a minute! We'll do this in steps, because I like steps!
1. using the water tool create the red line that zigazgs all over the place, this will create a lot of water and 3 islands touching each other (Cyprus and the 2 light blue things).
2. Obviously we don't want to keep the other 2 islands, we only want Cyprus! So the using the water tool again you create the yellow object, encircling the two unwanted islands! This will replace them with water, et voila, Cyprus is born!

Hope this helps!

P.S. Obviously when interpreting the redlines there are no abrupt turns, the red line flows continuously when there are crossovers...

When finished Amgen California Tour,ENECO Tour,Malaysia Tour and Tour Down Under?

Best Wishes

If someone have trouble finding information about a climb, try take a look at this page: https://www.climbbybike.com/climbs_sel...sp?CatID=0

414 pages with information about many many climbs in the world. Just click the arrows to the right, when you find the climb you need, and the information will show.

Hope I could help someone

For former stagemakers, that site is well known. But can come in handy for someone.

Will the all the stages made be in a patch for the PCMDaily Expansion pack? I know i've asked this question before. But never gotten a clear answer As far as i know

Is anyone going to make 2.2 & 1.2 races?

Some have already been made: https://cyanide-studio.com/forumPCM/vi...amp;t=3111

how do you get lines on the roads, i know you can change the road but i never seem to get lines on mine? also how do you add barriers, road blocks and signs etc....

and how can i edit the text written on the roads, searched but couldnt find it from last year?

hey, i'm working on a fantasy stage, and i'm making a mountan stage, the roads are all ok, but can't add start line etc. and when i use the "check stage" it says "bad rout" what is wrong?

edit: never mind, found it out my self

new Q: how do i change the angel of the camera?

using the mouse, hold in your middle button and scroll. also you can hold shift and use the arrow keys for a better view

how do you add cobble and gravel roads?
edit:explain like i am 3 years old.